Aluminum Entrance Gates

Aluminum Entrance Gates
Product Introduction:
Aluminum gives the point where architecture meets landscape a precise, light expression. Entrance gates can hold a fine vertical rhythm, preserve openness at the driveway and express a modern, natural or traditional direction through profile, proportion and panel form.
Send Inquiry
Description
Technical Parameters

Product Introduction

Aluminum gives the point where architecture meets landscape a precise, light expression. Entrance gates can hold a fine vertical rhythm, preserve openness at the driveway and express a modern, natural or traditional direction through profile, proportion and panel form.

The range includes five double-leaf driveway gates and one pedestrian gate. Each design can be adjusted for width, height, finish and operation, and coordinated with the fence range through the same finish and detail language. Images in this brief establish design direction; approved production photography should replace them before launch.

2

 

Why Aluminum

  • Rust-free. Aluminum needs no painting or polishing, including coastal and rainy sites.
  • Manageable weight. Leaves are lighter than steel, reducing hinge load and handling.
  • Weather-resistant finish. Powder coat or PVDF holds colour under long sun exposure.
  • Custom sizes. Opening width, leaf height, slat spacing and swing are confirmed per project.
  • Manual or motorized. Swing or sliding motors, safety sensors and manual release can be prepared.
  • Low maintenance. Wash with mild soap and water; no timber sealing is required.

 

Entrance Gate Range

Six designs cover modern, natural and traditional directions. Each gate can be specified for project width, height, slat spacing and operation, with a matching pedestrian gate.

Code

Design / Type

Mood

Finish shown

Best for

A01

AXIS
Architectural Drive Gate

Architectural

Matte charcoal

Driveways / courtyards

A02

GROVE
Woodgrain Courtyard Gate

Natural

Walnut woodgrain

Courtyards / garden entries

A03

FRAME
Paneled Entrance Gate

Architectural

Satin black

Residential driveways

A04

EDGE
Slimline Drive Gate

Architectural

Graphite

Modern homes / courtyards

A05

WILDWOOD
Motif Pedestrian Gate

Natural

Charcoal

Garden / side path

A06

BEAUMONT
Arched Estate Gate

Traditional

Chestnut bronze

Traditional homes / estates

 

Entrance Gate Details

A01 AXIS

Architectural Drive Gate

product-842-1191

Matte charcoal finish shown.

Narrow vertical slats create a changing surface as light moves across the entrance. A flush frame and disciplined rhythm keep the gate low, calm and unmistakably architectural.

Configuration: Double swing

Form: Close-set vertical slats

Finish shown: Matte charcoal

Best for: Driveways / courtyards

• Low visual mass

• Strong vertical rhythm

• Pairs with stone, render and glass

A02 GROVE

Woodgrain Courtyard Gate

product-842-1191

Walnut woodgrain finish shown.

A warm woodgrain finish softens an otherwise precise slatted facade. The louvered top rail and clean outer frame make it an easy bridge between natural and contemporary materials.

Configuration: Double swing

Form: Slatted panel with louver detail

Finish shown: Walnut woodgrain

Best for: Courtyards / garden entries

• Warm tactile tone

• Considered privacy

• Fits garden and facade

A03 FRAME

Paneled Entrance Gate

product-842-1191

Satin black finish shown.

A crisp outer border and inset vertical slats build a strong graphic face. Fine relief bands add just enough detail to suit classic-modern facades without overwhelming them.

Configuration: Double swing

Form: Inset panel with relief border

Finish shown: Satin black

Best for: Residential driveways

• Balanced symmetry

• Graphic silhouette

• Subtle decorative border

A04 EDGE

Slimline Drive Gate

product-842-1191

Graphite finish shown.

A slim upright profile and uniform slat field give this design a quiet modern presence. Its tall proportions and open top edge keep the boundary feeling light.

Configuration: Double swing

Form: Slim vertical slats

Finish shown: Graphite

Best for: Modern homes / courtyards

• Precise slim profile

• Unified slat field

• Quiet contemporary character

A05 WILDWOOD

Motif Pedestrian Gate

product-842-1191

Charcoal finish shown.

A single-leaf gate with a woodland motif and layered landscape base. It introduces a controlled point of personality at a side entrance or garden threshold.

Configuration: Single pedestrian leaf

Form: Slats with deer and landscape motif

Finish shown: Charcoal

Best for: Garden / side path

• Distinct focal detail

• Solid lower visual weight

• Rustic-contemporary character

A06 BEAUMONT

Arched Estate Gate

product-842-1191

Chestnut bronze finish shown.

Traditional scrollwork and a shaped crest bring a sense of established character. The warm bronze-toned finish makes the ornamental detailing feel grounded rather than overly formal.

Configuration: Double swing

Form: Arched crest with ornamental panels

Finish shown: Chestnut bronze

Best for: Traditional homes / estates

• Classic European reference

• Symmetrical composition

• Strong entrance presence

 

Materials and Finish

Element

Proposed specification

Why it matters outdoors

Main frame

6063-T5 aluminum, 2.0 mm wall

Rigid under wind and leaf loads

Slats / panels

1.5-2.0 mm aluminum

Light visual mass without flex

Standard finish

Polyester powder coat, 60-80 microns

UV and salt-spray resistance

Upgrade finish

PVDF fluorocarbon coating

Higher colour retention for coastal projects

Woodgrain

Heat-transfer film over powder coat

Timber tone without timber maintenance

Hardware

304 stainless hinges, latch and fasteners

No rust at moving parts

Posts

80 x 80 or 100 x 100 mm aluminum

Consistent gate and fence alignment

Critical joints

Internal brackets, reinforcement and welded nodes

Carry hardware and repeated operation

 

Finish Palette

 

 

 

 

 

 

Matte charcoal

Satin black

Graphite

Walnut

Chestnut

Espresso

 

Care and Warranty

  • Routine care. Wash with mild soap and water; no painting, sealing or timber treatment.
  • Hardware check. Inspect fixings and moving hardware annually; touch up chips promptly.
  • Coastal specification. Use PVDF finish and 304 stainless hardware for salt-air projects.

 

Gate System and Hardware

Configuration

Best use

Notes

Double swing

Driveways / courtyard entries

Pair of leaves, drop rod and optional automation

Single pedestrian

Side paths / garden entries

900-1,100 mm leaf, lock or smart lock

Sliding

Tight driveways / slopes

Top track or cantilever, motor and safety sensors

Manual operation

Residential / low-frequency use

Heavy-duty adjustable hinges; no power required

Motorized operation

High-frequency / hospitality

24 V DC motor, safety sensors and manual release

Hinges

All swing gates

Three adjustable 304 stainless hinges per leaf

Locks

Pedestrian and driveway gates

Stainless lock; key, keypad or smart-lock option

Gate posts

All openings

100 x 100 mm posts fixed to the approved foundation

 

  • Decide operation early. Motor, power, conduit and leaf travel must be agreed before posts are set.
  • Plan for safety. Automated gates require anti-crush, safety-edge, emergency-stop or locally required protection.
  • Match pedestrian gates. The matching pedestrian leaf should reuse the gate finish, slat rhythm and lock language.

 

Specifications and Customization

Item

Proposed standard

Customization

Gate leaf width

1,000-2,500 mm

Motorized or oversized leaves require review

Gate height

1,500 / 1,800 / 2,000 mm

Match fence height and local rules

Operation

Double swing / single swing / sliding

Confirm site clearance and motor type

Finish

Powder coat 60-80 microns

PVDF, woodgrain and custom RAL

Hardware

304 stainless

Smart lock, intercom, motor and sensors

Posts

100 x 100 mm

Heavy-duty posts to approved foundation

Privacy

Design-dependent

Slat spacing, panel form and backing

 

Installation and Site Requirements

Step

Work

Check

1

Confirm opening, swing direction, leaf travel and drainage

Clearance, slope and local rules checked

2

Set posts and fix the approved foundation

Posts plumb and spacing consistent

3

Hang leaves and adjust hinges after curing

Even gaps and smooth operation

4

Install lock, stop and drop rod

Stable closed position without movement

5

Commission motor, safety sensors and manual release

Stop, reverse and release tests passed

 

Frequently Asked Questions

Q: How does aluminum compare with steel?

A: Aluminum does not rust and is lighter, so large leaves are easier to hang and operate. Steel is heavier and needs continuing corrosion protection.

Q: Can the gate be motorized?

A: Yes. Swing and sliding gates can be prepared for a 24 V DC motor, safety sensors, keypad or intercom. Power and conduit should be planned before posts are set.

Q: Can a pedestrian gate match the driveway gate?

A: Yes. The pedestrian leaf can use the same finish, slat spacing and hardware language as the main gate.

Q: Can size and finish be customized?

A: Yes. Leaf width, height, operation and finish are confirmed per project, subject to site and local planning requirements.

Q: What finish suits a coastal site?

A: Specify PVDF coating and 304 stainless hardware, and state the salt-air environment in the order.

Q: What maintenance is required?

A: Wash with mild soap and water, inspect hinges, locks and motors annually, and touch up chips promptly.

 

Hot Tags: aluminum entrance gates, China aluminum entrance gates manufacturers, suppliers, factory

Send Inquiry
you dream it, we design it
We can create the aluminum alloy outdoor products
of your dreams
contact us