Product Introduction
Fences resolve boundary, privacy, airflow and architectural proportion at the same time. This range combines aluminum profiles with an independent panel system, so slat direction, density and finish can respond to the site instead of defaulting to a solid wall or timber fence.
The range includes horizontal louver, vertical slat, woodgrain, railing and traditional ornamental directions. Panels can step on level or sloping sites, while posts and rails remain aligned and can match an entrance gate. Images show design direction; approved production photography should be used before launch.

Why Aluminum
- Rust-free. Aluminum needs no painting or polishing, including coastal and rainy sites.
- Adjustable privacy. Slat width, spacing, louver angle and backing set the level of screening.
- Weather-resistant finish. Powder coat or PVDF holds colour under long sun exposure.
- Continuous runs. Panels and posts step with length and slope rather than fixed stock sizes.
- Flexible installation. Suits paving, low walls, terraces and garden boundaries.
- Low maintenance. Wash with mild soap and water; no timber sealing or pest treatment.
Boundary Fence Range
|
Code |
Design / Type |
Mood |
Finish shown |
Best for |
|
A07 |
SLATE |
Architectural |
Charcoal |
Side boundaries / screening |
|
A08 |
COLUMN |
Architectural |
Graphite |
Front boundaries / terraces |
|
A09 |
CEDAR |
Natural |
Chestnut woodgrain |
Garden boundaries / pool surrounds |
|
A10 |
HORIZON |
Architectural |
Espresso |
Rear yards / terraces |
|
A11 |
VERDANT |
Architectural |
Graphite |
Terraces / garden edges |
|
A12 |
BELMONT |
Traditional |
Black with chestnut highlights |
Traditional estates / front boundaries |
Boundary Fence Details
A07 SLATE
Louvered Privacy Fence
|
Charcoal finish shown. |
Horizontal aluminum louvers build privacy while retaining a measured line of sight. The repeated rhythm works especially well against masonry, planting and modern facades. Configuration: Panel and post system Form: Horizontal aluminum louvers Finish shown: Charcoal Best for: Side boundaries / screening • Layered privacy • Horizontal architectural rhythm • Pairs with masonry and planting |
A08 COLUMN
Vertical Slat Estate Fence
|
Graphite finish shown. |
Broad slats alternate with fine gaps to create a confident, rhythmic boundary. The balanced spacing keeps sightlines open around planting and exterior circulation. Configuration: Panel and post system Form: Broad vertical slats Finish shown: Graphite Best for: Front boundaries / terraces • Privacy with openness • Calm repeating cadence • Works at garden and street scale |
A09 CEDAR
Woodgrain Slat Fence
|
Chestnut woodgrain finish shown. |
Deep woodgrain-tone slats introduce warmth without relying on timber. Fine vertical spacing lets the fence sit lightly within planting and landscape-led gardens. Configuration: Panel and post system Form: Vertical slats with fine spacing Finish shown: Chestnut woodgrain Best for: Garden boundaries / pool surrounds • Natural tonal warmth • Light vertical rhythm • Soft integration with greenery |
A10 HORIZON
Horizontal Privacy Fence
|
Espresso finish shown. |
Wide horizontal rails produce a calm, layered surface with a strong relationship to modern architecture. The open spacing keeps the panel visually lighter than a solid wall. Configuration: Panel and post system Form: Wide horizontal rails Finish shown: Espresso Best for: Rear yards / terraces • Quiet horizontal composition • Layered privacy • Strong architectural alignment |
A11 VERDANT
Vertical Bar Railing
|
Graphite finish shown. |
Simple vertical bars and a slim top rail create an open perimeter with minimal visual interruption. A natural fit for terraces, garden edges and open-air circulation. Configuration: Panel and post system Form: Simple vertical bars Finish shown: Graphite Best for: Terraces / garden edges • Maximum visual openness • Low visual weight • Understated modern line |
A12 BELMONT
Ornamental Estate Fence
|
Black with chestnut highlights finish shown. |
Curved scrollwork, repeated finials and a richer finish reference classic wrought-iron language while staying true to aluminum construction. Configuration: Panel and post system Form: Repeated scrollwork and finials Finish shown: Black with chestnut highlights Best for: Traditional estates / front boundaries • Classic ornamental silhouette • Fine decorative repetition • Layered dark and bronze tones |
Materials and Finish
|
Element |
Proposed specification |
Why it matters outdoors |
|
Main frame |
6063-T5 aluminum, 2.0 mm wall |
Rigid and straight under wind load |
|
Slats / panels |
1.5-2.0 mm aluminum |
Light visual mass without flex |
|
Standard finish |
Polyester powder coat, 60-80 microns |
UV and salt-spray resistance |
|
Upgrade finish |
PVDF fluorocarbon coating |
Higher colour retention for coastal projects |
|
Woodgrain |
Heat-transfer film over powder coat |
Timber tone without timber maintenance |
|
Hardware |
304 stainless brackets, screws and fasteners |
No rust at exposed fixings |
|
Posts |
80 x 80 or 100 x 100 mm aluminum |
Maintains a continuous panel line |
|
Critical joints |
Internal brackets, reinforcement and welded rails |
Carry wind load and keep panels stable |
Finish Palette
|
|
|
|
|
|
|
|
Matte charcoal |
Satin black |
Graphite |
Walnut |
Chestnut |
Espresso |
Care and Warranty
- Routine care. Wash with mild soap and water; no painting, sealing or timber treatment.
- Hardware check. Inspect fixings and moving hardware annually; touch up chips promptly.
- Coastal specification. Use PVDF finish and 304 stainless hardware for salt-air projects.
Fence Panel and Post System
|
Part |
Standard options |
Notes |
|
Panel width |
1,500 / 1,800 / 2,000 mm |
Custom widths to suit bays and breaks |
|
Panel height |
1,200 / 1,500 / 1,800 / 2,000 mm |
Confirm privacy and local height rules |
|
Slat direction |
Horizontal / vertical / louvered |
Match the selected design |
|
Post |
80 x 80 / 100 x 100 mm |
Caps, base plates or concealed fixings |
|
Privacy level |
Open / layered / near-solid |
Set by spacing, louver angle or backing |
|
Fixing |
Concealed brackets and stainless screws |
Clean face and serviceable panels |
|
Top and bottom rail |
Welded aluminum |
Maintains rigidity and a clean edge |
|
Matching gate |
Pedestrian or driveway |
Same finish, slat rhythm and post language |
- Set privacy first. Louver angle, slat spacing and backing determine sightlines and airflow.
- Step with the slope. Keep each panel vertical while the post height and top line follow the site.
- Allow service. Use removable fixings for cleaning, panel replacement and local adjustment.
Specifications and Customization
|
Item |
Proposed standard |
Customization |
|
Panel width |
1,500 / 1,800 / 2,000 mm |
Customized to bays, openings and post positions |
|
Panel height |
1,200 / 1,500 / 1,800 / 2,000 mm |
Confirm privacy and local rules |
|
Slat spacing |
20 / 40 / 80 mm |
Adjusted by design and privacy level |
|
Louver angle |
0-45 degrees |
Sets sightlines, airflow and screening |
|
Finish |
Powder coat 60-80 microns |
PVDF, woodgrain and custom RAL |
|
Posts |
80 x 80 / 100 x 100 mm |
Height and foundation confirmed by site |
|
Privacy |
Open / layered / near-solid |
Backing, infill or denser slats optional |
Installation and Site Requirements
|
Step |
Work |
Check |
|
1 |
Measure bays, slope, corners and post positions |
Run lengths, openings and clearances checked |
|
2 |
Set posts by bay and fix foundations |
Posts plumb and top line consistent |
|
3 |
Install panels and rails; check privacy and gaps |
No racking and consistent spacing |
|
4 |
Close corners and building junctions |
Clean seams and secure fixings |
|
5 |
Install matching gate or local screening accessory |
Finish, rhythm and operation aligned |
Frequently Asked Questions
Q: How do I choose the privacy level?
A: Louver angle, slat spacing and rail depth determine whether the fence is open, layered or near-solid.
Q: Can the fence follow a slope?
A: Yes. Each panel remains vertical while post heights and the top line step with the site.
Q: Does aluminum fence rust?
A: No. Use PVDF coating and 304 stainless fasteners for coastal projects.
Q: Can width, finish and spacing be customized?
A: Yes. Panel width, height, finish and slat spacing are confirmed per project, subject to local fence rules.
Q: Can fences match the entrance gates?
A: Yes. The ranges can share finishes, slat rhythm and post language.
Q: What maintenance is required?
A: Wash with mild soap and water, inspect brackets and screws, and touch up chips. No timber sealing or pest treatment is required.
Hot Tags: aluminum boundary fences, China aluminum boundary fences manufacturers, suppliers, factory







